Replacement starts with fitment, and this monforts stenter machine chain is built to 1:1 compatible pitch, hole position and assembly size, so it installs on the existing rail without modification. Where an oven runs technical textiles or long shifts, the same design is supplied as a high temperature stenter chain with tempered, surface-hardened links that hold pitch under sustained heat. Measure the chain you have today, send the details, and we confirm the variant and length before you commit to a bulk order.

Check Compatibility & Price Request a Sample

Monforts Stenter Chain | High Precision Tenter Chain for Monforts Heat Setting Machine

Build sheet

What the order actually contains

One page of facts, no guesswork: material, machining route, fitment standard and the commercial terms that decide whether you order a single sample or a full line set.

Product name	Monforts Stenter Chain / Monforts Tenter Chain
Main material	High-strength alloy steel with a wear-resistant hardened layer
Processing route	Integral forging, CNC precision machining, high-temperature aging treatment
Fitment standard	Chain pitch, hole position and assembly size stated as 1:1 standard compatible for direct installation
Machine compatibility	Monforts Montex series stenter machines; also stated compatible with mainstream Likun and Lixin stenters
Clip compatibility	Cooperates with Monforts single-use and dual-use stenter clips
Chain length	Customised per machine model; confirmed from your measured length before production
Minimum order	1 piece sample supported; bulk supply for factory maintenance programmes

Self-identification

Identify your chain before ordering

Five readings turn a vague replacement request into a confirmed order. Take them with the machine stopped, the chain clean and a steel rule or caliper in hand.

Step 01

Record the machine identity

Copy the nameplate model and serial number, then note the number of chambers and the working door width. This is the field that decides which variant row you sit in.

Step 02

Measure the pitch

Take the centre-to-centre distance between two consecutive link pins along a straight run, never across a curve or a worn section. Repeat at three points and send the average.

Step 03

Map the hole position

Note where the pin bore sits relative to the link edge, then photograph one link end-on with a rule in the frame. Hole position is checked alongside pitch, not instead of it.

Step 04

Capture assembly dimensions

Measure overall link height and width, plate thickness, and roller or bush diameter. These are the numbers that prove a 1:1 match on the drawing.

Step 05

Count the chain length

Count links across a full loop, or measure the run length on one side. State clearly whether you need a complete loop or a repair section cut from stock.

Step 06

Send, then wait for confirmation

Send the readings with two photographs through the contact page. The variant, cut length and accessory list are confirmed in writing before anything goes into production.

Variant selector

Standard or high-temperature chain?

The two variants share one geometry and one fitment standard. The choice is driven by what the oven does all week, not by what looks heavier on the shelf.

Standard chain

For conventional heat-setting duty

Woven, knitted and blended fabric running at normal line temperatures
Routine wear-part replacement on a line that already holds width
Hardened surface treatment for extended service life between changes
Fine-tuned roller and gap structure for low-friction, low-noise running

Choose this when the complaint is simply that the old chain is worn, noisy or stretched, and the oven profile has not changed.

High-temperature variant

For hot ovens, technical textiles and long shifts

High-temperature tempering to resist thermal elongation
Low thermal deformation with stable pitch retention across the run
Surface hardening for a load-bearing, continuous-production track
Suited to technical textiles where width consistency is critical

Choose this when pitch growth, width drift or selvedge variation has already appeared on a hot range, or when the line runs near the top of its profile for long shifts.

Oven zoneWhich chambers run hottest

Fabric typeIncluding technical textiles

Door width & loadWorking width and fabric weight

Shift hoursContinuous or batch pattern

No single temperature figure is published for either variant, because the right answer depends on all four inputs. Send them together and the recommendation is confirmed against your oven data.

Scenario to specification

Match the problem you have to the part you order

Four situations account for most Monforts chain inquiries. Each one points to a different specification and a different buying decision.

Fabric width drifting on a hot range

Width loss and selvedge variation on a hot line usually trace back to pitch growth rather than to the clips.

Confirm: oven zone and dwell time against measured pitch.

Decision: order the high-temperature tempered variant and start with a sample section.

See the chain specification

Routine wear replacement on a woven line

The chain is noisy, stretched or simply past its cycle, and the oven profile is unchanged.

Confirm: pitch, hole position and loop length from the existing chain.

Decision: standard chain at 1:1 compatible geometry; one sample piece is enough to verify fit.

Check compatibility and price

Full overhaul after a long service run

Chain, clips, pin plates and brush wheels have all reached the end of their cycle together.

Confirm: clip type currently on the rail — single-use or dual-use.

Decision: renew the running gear as one matched set so the selvedge contact geometry stays consistent.

Request a set quotation

New clips onto an existing chain

Clips are being replaced but the chain stays in service for another cycle.

Confirm: whether the rail carries single-purpose or dual-purpose clips, since load paths differ.

Decision: order clips against the measured chain, not against the machine model alone.

View the single-purpose clip

Confirm the fitment before you place a bulk order

Send the machine model, pitch, hole position, assembly dimensions and loop length. You get back a confirmed variant, a customised length and a quotation for the chain or the full running set.

View Product & Price

Frequently Asked Questions

What information is shown for this product?

Review the product details, images, and specifications presented on the official product page.

Where can i check the intended application?

Use the application and use-case information published on the official product page.

Which specifications should i confirm before ordering?

Confirm the specifications and options listed for the exact product variant before placing an order.

Where can i check available options?

Check the official product page or ask the supplier about options shown for the selected product.

How can i request product information?

Use the official contact or inquiry path provided on the site.

What should i include in an inquiry?

Include the product page, intended use, required quantity, and any specifications you need the supplier to review.

Winwell: About Us; Contact Us; Blog; FAQs

All Products: Stenter Machine Clip; Stenter Machine Chain; Stenter Machine Pinplate; Stenter Machine Brush; Stenter Machine Pin Holder; Stenter Machine Protector; Stenter Machine Other Parts; Rotary Printing Screen; Rotary printing Other Parts

Contact Us: Room 101-07, No.196, Lanling Subdistrict, Tianning District, Changzhou, Jiangsu Province, China; molly@cnwinwell.com; 0086 17712317161

Newsletter: Subscribe to access product market trends, priority quotation services and trade cooperation updates.

Leave a message

Name *

Email *

Message *

Verification Code *

Click to verify

Monforts Stenter Chain Fitment Guide